Nxg-technology NX-Si605 Bedienungsanleitung PDF herunterladen (Seite 1)

(Continued on reverse)

Where To Place Your In-Wall Speakers (Fig. 2)

Placement can make all the difference in how your speakers sound, and how easy they will be to install.

Carefully consider where your speakers should be positioned. For optimum performance, speakers should

be mounted to the left and right of the main listening position and a minimum of 8 to 10 feet apart. A void

mounting speakers in stud cavities containing electrical wiring, heating ducts, water pipes, etc. Make sur e

the wall or ceiling materials are sturdy enough to support the weight of the speakers.

In-Wall Placement: Optimum performance will be achieved when your speakers are mounted at ear level

or slightly higher. If you desire to mount them higher in the wall, turn the speaker over so the tweeter

is closer to the listening area.

In-Ceiling Placement: Optimum performance will be achieved when your speakers are mounted to

the left and right of the main listening area.

Pivoting Tweeters (Fig. 3)

The tweeters in all NXG Signature Series speakers may be adjusted, allowing you to focus the speakers’

high frequency output to better fit the listening area. The overall smoothest response is achieved with the

tweeter facing straight out; however, you may find the sound more pleasing by aiming tweeters toward a

particular listening area. To adjust the tweeter, apply pressure on the ring surrounding the tweeter with your

thumb or finger.

Tweeter/Midrange Level Adjustments (Fig. 4)

Tweeter and midrange level controls allow you to tailor the speakers’ frequency response to better

match the room’s acoustics. As an example, if a room has a hardwood floor, which makes it acoustically

brighter sounding, you may want to adjust the tweeter and midrange levels to compensate. You can

experiment with both levels to find the sound that’s most pleasing to you in your particular listening

environment.

Speaker Installation In Existing Construction (See Fig. 5 on reverse)

Once you have selected the location for your speakers, you are ready to install them.

You will need the following:

• Stud Finder • Drill & Drill Bits • Wire Cutter/Strippers

• Pencil • Utility Knife or Drywall Saw • Small Level

• Masking Tape • Phillips Screwdriver • Speaker Wire

NXG recommends the use of 16-gauge wire minimum. For wire options consult your retailer or custom

audio contractor.

1. NXG Signature Series Speakers are designed to be installed in the wall area between studs. Using a

stud finder, make sure you are between two studs. Using the supplied template and a level to ensure your

template is straight, tape the template to the wall and lightly trace around the outside with a pencil.

2. Cut the hole using your drywall saw. You may want to start with a small hole in the center of the

outline. This will allow you to check for any obstructions that may exist behind the desired location.

CAUTION: Be certain electrical wiring, water pipes or heating ducts do not interfere in the planned instal-

lation areas prior to drilling or cutting the wall.

3. Run speaker wire from your amplifier or speaker switching device to the speaker location.

4. If you like the standard white finish of your NXG speakers, skip to step 5, but if if you want your

speakers to blend in with a colored wall or ceiling, now is the time to paint your speaker’s outer frame

and perforated grille. The speaker’s outer surface will accept ordinary latex wall paint or aerosol spray

paint. Because the speaker baffle surface behind the grille should remain unpainted, you will need to

cover this area with the supplied paint mask. Cover the speaker’s interior black surface, woofer and

tweeter. Paint the outer speaker frame and grille separately. (Grille painting hint: Use a paint roller that

is nearly out of paint to first paint the inside of the grille, then the outside. This will avoid paint filling

the grille perforations.)

Thank you for choosing NXG Signature Series Loudspeakers. Like all NXG products, great care has

been taken in their design. Their combination of advanced engineering and state-of-the-art materials

will provide you with years of listening pleasure, while blending smoothly into your home’s decor.

Before you get started, it is a good idea to identify all the parts and hardware (See Fig. 1).

FIG. 1

Grille

Painting

Mask

Cutout

Template

Speaker with self-contained

mounting clamps

FIG. 2

NXG Signature Series In-Wall Speakers can be used

as rear surround sound channels by placing them

(1) behind, (2) on each side of viewer, or (3) in the

ceiling just behind viewing position. They also make

excellent front channel home theater speakers (4).

Adjust tweeter & midrange levels as shown

FIG. 4

FIG. 3

Press on the

edge of the

tweeter to

rotate

NX-Si605 6

˝ Two-Way

In-Wall Speaker System

Black Grille

Adhesive

1 2

Inhaltsverzeichnis

Seite 1 - In-Wall Speaker System

(Continued on reverse)Where To Place Your In-Wall Speakers (Fig. 2)Placement can make all the difference in how your speakers sound, and how easy they

Seite 2 - Operational Check

(Continued from front)5. Attach the wire to the input terminals on the rear of the speaker.Remember to maintain proper polarity with the amplifier by

Kommentare zu diesen Handbüchern

Keine Kommentare

Nxg-technology NX-Si605 Bedienungsanleitung Seite 1

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Akustik Nxg-technology NX-Si605 herunter. NXG Technology NX-Si605 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Nxg-technology NX-Si605 Bedienungsanleitung Seite 1

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Akustik Nxg-technology NX-Si605 herunter. NXG Technology NX-Si605 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Akustik Nxg-technology NX-Si605