Nxg-technology NX-SSVC6 - Six Zone Automatic Impedance Matching S Bedienungsanleitung PDF herunterladen

PAI

(Continued on reverse)

Congratulations on choosing the NX-SSVC6 Impedance Matching Speaker Selector

Like all NXG products,

great care has been taken in its design. We hope the combina-

tion of advanced engineering and state-of-the-art

materials will provide you with a

lifetime of listening pleasure.

Introduction

The NX-SSVC6 is a resistor based, impedance matching speaker selector/volume

controller used for connecting six pairs of (4 ohm or 8 ohm) speakers while main-

taining a safe impedance load for your receiver or amplifier. The NX-SSVC6 allows

you to adjust the volume of any pair of speakers independently. Additionally, each pair

of speakers can be selected (on/off) independently in any combination, by the push-

buttons on the front of the unit, without concern for amplifier loading.

FIG. 2

Wiring Instructions

Follow the suggestions that came with your receiver or speakers for determining the correct wire gauge needed to connect your NX-SSVC6

speaker selector. Lay out all wire runs from each speaker location and your receiver to your selector. Remove the connector blocks from the

selector and make all the connections to the connector blocks as shown in Figure 1. (If your receiver or amplifier has both A & B outputs con-

nect your NX-SSVC6 to your receiver’s A outputs.) Pay close attention to make certain all strands of bare wire are completely inserted into the

connector properly and that no loose strands are outside the connector hole. Any loose strands could possibly touch another wire and short

the receiver’s output. After you have tightened the screw terminals to secure the wires, insert the connector block back into your selector as

shown in Fig 2.

Features and Benefits

1. Connect and safely control up to six speaker pairs with one amplifier.

2. Built in automatic impedance protection circuitry engages without the need for user involvement.

3. Individual room on/off control via the front mounted pushbuttons.

4. Individual room volume via the front mounted 12 position rotary controls.

5. Heavy-duty screw-type connectors, capable of accepting up to 12 AWG wire, provide positive hookup to input and output wires.

6. Isolated left/right circuit grounds provide safe connection for amplifiers with floating grounds or bridged configuration.

7. High quality construction throughout provides excellent reliability, accurate switching, and noise-free volume control.

8. Intelligent design allows simple installation, easy connection, and trouble-free operation.

9. Rubber feet prevent scratching and keep selector in place during operation.

FIG. 1

NX-SSVC6 6-Zone Automatic Impedance Matching

Speaker Selector with Volume Controls

Shown using

adhesive room labels

Volume control

ON-OFF Button

Button In = ON

Button Out = OFF

FRONT VIEW

REAR VIEW

1 2

Inhaltsverzeichnis

Seite 1 - Features and Benefits

PAIR 6PAIR 5PAIR 4PAIR 3PAIR 2PAIR 1(Continued on reverse)Congratulations on choosing the NX-SSVC6 Impedance Matching Speaker Selector.Like al

Seite 2 - Specifications

(Continued from front)Power Handling: 100 watts RMS per channelFrequency Response: 20 Hz – 22 kHz (+0dB, -0dB)On/Off Selector Type: Noise-free, front

Kommentare zu diesen Handbüchern

Keine Kommentare

Nxg-technology NX-SSVC6 - Six Zone Automatic Impedance Matching S Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Nxg-technology NX-SSVC6 - Six Zone Automatic Impedance Matching S herunter. NXG Technology NX-SSVC6 - Six Zone Automatic Impedance Matching Speaker Selector User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Nxg-technology NX-SSVC6 - Six Zone Automatic Impedance Matching S